Flue Type Gas Water Heaters
Introduction of Natural Gas Hot Water Heater
1. China Flue mounted gas water heater is developed on flueless water heater. The oxygen needed for combustion is taken from indoor, and the smoke produced by combustion is emitted to the outside through the flue. 2. Working principle of natural gas hot water heater: cold water enters the water heater, and reaches heat exchanger through filter and water-gas linkage assembly, and then hot water comes out. Gas enters the water heater, and flows through filter, gas stabilizer, magnetic valve, gas control valve, gas valve and gas nozzle of the water-gas linkage assembly, and then reaches combustor. Mixture of gas and air is lighted, and flames appear in the combustor. Smoke with high temperature flows through heat exchanger, and enters anti-downdraft exhaust hood, and gets mixed with cold air and emitted to the outside through flue.Features:
1. Compared with the direct gas emission of flueless gas water heater, flue type emits gas to the outside through smoke vent, which solves the problem of indoor air pollution to some extent, and it is a remarkable progress in technical safety for gas water heater.2. Natural gas hot water heater is popular in the market due to its well-developed technique and low price.
3. However, the gas needed for combustion by this type is taken from indoor, with low combustion strength and bulky size, as well as problems in installation and potential risks. Therefore, China flue mounted gas water heater will be out of market gradually for the sake of users and environment.
Advantages:
1. It is of high security and endowed with fast heating speed and stable temperature.
2. It has large water flow which can be increased to 8-10L per minute.
3. China Flue mounted gas water heater is with little incrustation and tiny space occupation.
Vanward Products
Gas Water Heater
Comparison of the Flue Type, Forced Exhaust Type, Forced Exhaust and Air-Supply Type:
Flue Type |
Forced Exhaust Type |
Forced Exhaust and Air-Supply Type |
Not safe enough The combustion product generated during combustion is emitted directly to the bathroom, and the air for combustion is taken from the bathroom too. It is easy to cause CO poisoning and insufficient oxygen supply, so it can’t be installed inside the bathroom. |
Much safer than flue type The combustion product generated during combustion is emitted out of the bathroom through a flue, but the air for combustion is still taken from the bathroom, which may cause hypoxia. It is highly suggested not to install this type of gas water heater inside the bathroom. The difference between the flue type and forced exhaust type is that the forced exhaust type has a fan to forcedly blow or vacuum the combustion product out of the bathroom through a flue, but the China flue mounted gas water heater is to naturally emit the combustion product out of the bathroom with a flue (not included, optional). Therefore the evacuation of the combustion product of the forced exhaust type is more complete than that of flue type. |
The safest of all The combustion product generated during combustion is forcedly emitted out of the bathroom through a flue, meanwhile the air for combustion is forcedly inhaled from outside through the flue, so it wouldn’t consume or pollute the air inside. It is the safest and the only type that can be installed inside the bathroom. |
|
|
|
Notes of Flue Mounted Gas Water Heater:
1. It cannot be installed inside the bathroom.
2. Flue must be connected to the outdoor.
3. Flue horizontal tube protrudes the outdoor, and the top shall be connected with vertical tube (Adding hood at the top is also acceptable).
Care and Maintenance:
1. China Flue mounted gas water heater shall not be installed in the bathroom. It can be installed in the back porch, if there is one. Otherwise, it shall be installed on the kitchen wall close to window for ventilation in time.
2. There shall be no inflammables or explosives around the water heater, and it cannot be too close to stove. There shall be no electric wire on the water heater, and no inflammable in the flue.
3. The diameter of water heater’s flue mouth must be in consistent with that of the flue. Flue cannot be turned unless 30cm above the flue mouth of the water heater.
4. Fire view hole of water heater shall be between 1.55m and 1.68m above the ground. For special occasions, the range can be properly broadened, but cannot affect the third item.
5. Flue installation length of natural gas hot water heater shall not be over 2 meters, and vent cap shall be installed at the outside of flue mouth.
Typical Type:
Type |
JSD20-10M1 |
JSD24-12M1 |
JSD32-16M1 |
Rated heat load(kW) |
20 |
24 |
32 |
Rated capability of hot water supply (△T=25℃) |
10kg/min |
12kg/min |
16kg/min |
Rated gas pressure |
Liquefied petroleum gas 2800 pa |
||
Natural gas 2000 pa |
|||
Manufactured gas 1000 pa |
|||
Control method |
By outlet valve |
||
Exhaust method |
Flue type |
||
Applicable water pressure (Mpa) |
0.02-1.0 |
||
Gas entrance |
G1/2 or G3/4 |
||
Cold water inlet |
G1/2 |
||
Hot water outlet |
G1/2 |
||
Product size(mm) |
636×350×225 |
636×350×225 |
680×410×223 |
Package size(mm) |
735×405×300 |
735×405×300 |
780×468×300 |
Gross weight/net weight(kg) |
12.8/11.3 |
13.3/11.8 |
18.3/15.1 |
Container number 20'/40'/40'HQ |
320/660/768 |
320/660/768 |
250/530/620 |
JSD20-10M1/JSD24-12M1/JSD32-16M1 | JSD20-10P1/JSD24-12P1/JSD32-16P1 |
JSD12-6CL/JSD14-7CL/JSD16-8CL/JSD20-10CL | JSD12-6CR/JSD14-7CR/JSD16-8CR/JSD20-10CR |
JSD12-6CA/JSD14-7CA/JSD16-8CA | JSD12-6CC/JSD14-7CC/JSD16-8CC |
Related Products:
-
Email: betty@roll-forming.cn
©Guangdong Vanward New Electric CO., LTD
Tel: +86-21-6036873
Fax: +86-21-6036873
Email:
sales@vanward.cc